FINALLY GOT AROUND TO INSTALLING MY CIRO BIG ASS CUP HOLDER ON MY 2020 INDIAN ROADMASTER DARK HORSE. TOTAL TIME WAS ABOUT 10-12 MINS INCLUDING ME PUTTING THE WRONG THREAD BOLTS IN THE FIRST TIME. BUT OVERALL I’M PLEASED WITH IT.
All right we back well i’m back get another one so today i’m going to attempt to install my big ass cup holder i’ve already got a little round boxes and taking it out of the box this is the perch mount these are the instructions pretty clear cut take the two bolts out put the perch on with the spacers make sure you have the correct bolts go over here because
It’s not gonna lie i tried it at first didn’t pay attention just notice that these were longer so i want to use those these are you know the coarse threads and these are five threads so you need to pay attention to the threads that you’re taking out so you’ve got the coarse thread see how it’s wider of course and we have fine threads here’s thinner country
Two spacers and this is on a 20 20 indian chieftain dark horse so yeah excuse me trying to get my camera work together so i loosen these up a little bit right here it did line up you wanna know how it lines back up now i’ve already loosened it but it should be tight right there so the line right here and line right here so be in alignment so this might be a
Little god damn it might be a little shaky because i’m trying to do it with two hands without mounting the camera maybe i should set the camera up i probably have been smarter anyway come on hocus focus okay so this is our threads as you can see they’re fine threads once the camera focuses okay so we have fine thread so if you don’t know how to match threads up
We’ll know where they’re fine of course this is the one i just took out these of course okay see how they will not fit in the grooves with each other and these are fine and they should fit perfectly in the grooves with each other that’s how you know if you gotta find the course so get the other one out the bottom one that’s what happens when i get excited about
Doing some stuff i just start going and then being properly prepped like i should if i’m a record so y’all kind of getting this raw so probably gonna drop some didn’t put a towel on my tank because i didn’t know the right stuff i’m supposed to do so let’s hope i don’t break a chip anything original factory boats these are extended ones so let’s find our perch
This purge mount and i am going to mount my kind of upside down like that so if the cup is lower versus up the cup would be higher cup low high all right i’m gonna pause for the calls and try to get it set up and then i’ll come right back okay so we’re back i have put the the fine defined screws in there this is your spacer it comes with two spacers this
Is the boat this is your perch this is the mount so i’m going to probably give it up right so you got the beveled edge right here and the flat edge right here and this line in that line should line up that’s how it was when i loosened it that’s how i want to be when i tighten it back up it’s tight it’s tight there’s gonna be a little gap because we got
The spacers in here so those aren’t for so long before they start running out of threads but that’s it right there take your uh the screw put it over the ball so you have the flat side and then the threaded side set that up right there got the actual cup holder the female in where the ball goes so just pop on don’t take much force you tighten that up once
You get it flush there we go it’s fresh now so i did not test fit this so y’all kind of going along with what i got right now and as you see you can adjust the angle of the holder just by simply loosening that so much of the damn thing cause you better hold my big ass cup too all right so my tools out of the way oh locate my big ass cup hold on there we go
Big tumbler gotcha let’s see here’s that water in it it’s pretty much real good ride height i wonder if it’s going to block my music though coming out of the left speaker let’s see let me get on let’s see yeah i can’t see now the controls but maybe i can loosen it and turn it in some yeah that’s definitely going to block my music oh easy killer all right so
I’m not thirsty while i’m riding just pick that thing up that thing goes give me a little sip left hand back in the cup holder keep on pounding i can reach the controls around the cup it’s not in the way the only concern with me having it this low is it really going to block that speaker and height the music comes out because on these the music is more surround
Sound versus in your face so i don’t know if it starts to block it i’m gonna flip this thing up and that cup holder is gonna be up here and it’s gonna be a little taller which is basically the reverse of what i just did so that’s it this is my all black big ass cup holder fitting my tumblr this is my install pretty damn simple sorry for the camera work i just
Uh decided to pick up the phone and go ahead and start recording i’ll be riding here the next day or two so i’ll let you guys know how that turned out leave me a comment if you have one and you have it placed in a different area or a different spot that’s better than what you see on mine then please let me know oh the bars are just the indian mid-rise bar there’s
Nothing special this is not necessarily the stock bars so that’s that’s what i got so i don’t know man we’ll find out but until then peace
Transcribed from video
CIRO BIG ASS CUP HOLDER INSTALL ON 2020 INDIAN ROADMASTER DARKHORSE By Team McMath – McMath Autos